歡迎訪問常州市邦源幹燥機械有限公司!
常州市邦源幹燥機械有限公司

Changzhou bangyuan drying Machinery Co.,Ltd.

福利在线免費服務福利在线:18261199989
福利在线
    常州市邦源幹燥機械有限公司
    福利在线:计先生 18261199989
    電 話:0519-88913680
    傳 真:0519-88913680
    郵 箱:2870078927@qq.com
    地 址:江蘇省常州市鄭陸鎮焦溪工業園

夏日-雙錐真空幹燥機溫度過高解決辦法

发布时间: 2018-07-30
关键词:夏日-雙錐真空幹燥機溫度過高解決辦法
首先:确定干燥设备散热管有没有堵塞 ,导致热量无法散出,,会使得双锥真空幹燥機的温度升高。还有尽量避免双锥真空幹燥機被太阳直射,如果放在场内摆放,双锥真空幹燥機应该避免前后两台靠着摆放,不通风。通风不好一系列问题都可以引发了干燥机温度过高。

First of all: to determine whether the drying equipment heat pipe is blocked, resulting in heat can not be dissipated, will make the double cone vacuum dryer temperature increased. As far as possible to avoid the double cone vacuum dryer by the sun directly, if put in the field, double cone vacuum dryer should avoid the two sets before and after placing, not ventilated. A series of problems caused by poor ventilation can cause the dryer temperature to be too high.




及時清理好發動機機身的油汙和塵土,保證發動機保持良好的散熱。

Clean up the oil and dirt of the engine fuselage in time to ensure that the engine keeps good heat dissipation.



應認真做好破碎機設備維護保養工作,定期對設備進行全面檢查,做好設備維修保養,更換發動機“三濾”及機油,更換或調整皮帶,檢查風扇、水箱、發電機、壓縮機等部件是否能正常運轉。

The maintenance work of the crusher equipment should be conscientiously done. The equipment is regularly checked, the equipment is maintained, the engine "three filters" and the oil are replaced, and the belt is replaced or adjusted to check whether the parts of the fan, water tank, generator, compressor and other components can operate normally.




因爲熱脹冷縮原理,高溫會使破碎機的零部件膨脹,導致各部件的咬合處産生更多的摩擦和偏差,不僅會影響生産進度,摩擦還會使溫度進一步升高;

Because of the principle of heat expansion and contraction, high temperature will inflate the parts of the crusher, resulting in more friction and deviation at the biting place of each component, which will not only affect the production progress, but also increase the temperature.





檢查冷卻系統、燃油系統否通暢,並更換老化的電線、插頭、油管、螺絲、緊固燃油管路,防止燃油泄漏。

Check the cooling system, fuel system is unobstructed, and replace aging wires, plugs, tubing, screws, fasten fuel pipelines to prevent fuel leakage.




爲設備更換恰當的機油粘度等級,一般夏季機油粘度等級要比其他時候適當高一些。發動機機油及各處潤滑油需更換使用夏季用油,油量合適,經常檢查是否有漏油情況,特別是燃油,應及時補充。

For the equipment to replace the appropriate oil viscosity grade, the general viscosity level of summer oil is higher than that of other times. Engine oil and lubricating oil everywhere need to be replaced and used in summer. The amount of oil is suitable. Check whether there is oil leakage, especially fuel oil, should be added in time.



夏季高溫,增加設備故障率以及火災發生率,請您務必爲每台機器隨機配備1-2台滅火器,以防不測。

Summer high temperature, increase equipment failure rate and fire incidence, please be sure to each machine randomly equipped with 1-2 fire extinguishers, in case of accidents.



夏季室外溫度高,高溫容易對設備造成不良影響,建議您無論設備處于停機還是工作狀態,都盡量保證設備放置在蔭涼處,如夏季高溫可爲設備搭建臨時遮陽棚,避免設備長時間在太陽下暴曬。設備日常保養爲保持破碎機設備處于^好的工作狀態,並且可以隨時可以投入運行,減少故障停機時間,提高破碎機完好率、利用率,減少破碎機磨損,延長破碎機使用壽命,一定要做到定期保養,制定好合理的保養計劃,正確處理使用保養和修理的關系,這一點千萬不能大意。設備軸承保養破碎機軸承工作很重要,因爲軸承部位是^容易壞掉的,在使用中磨損比較大,所以需要經常保養,經常加油才能增加軸承的使用壽命。設備潤滑保養在破碎機日常工作中要注意和及時做好摩擦面的潤滑工作,這樣可保證設備的正常運轉,並且有效延長破碎機使用時間。一般情況下加入軸承座內的潤滑脂爲容積的50-70%,每三個月必須更換一次,換油時應用清潔的汽油或煤油仔細地清洗軸承滾柱的跑道。

In summer, the outdoor temperature is high and the high temperature is easy to have bad effects on the equipment. It is suggested that the equipment should be placed in the shade, if the equipment is in a stop or working state. For example, a temporary sunshade can be built for the equipment in summer, so that the equipment can avoid exposure to the sun in the sun for a long time. The daily maintenance of the equipment is to keep the crusher equipment in the best working condition, and can be put into operation at any time, reduce the failure time, improve the integrity and utilization of the crusher, reduce the wear of the crusher and prolong the service life of the crusher. It is necessary to ensure regular maintenance and make a reasonable maintenance plan. It is very important not to deal with the relationship between maintenance and repair. Equipment bearing maintenance crusher bearing work is very important, because the bearing part is the most easy to break, in the use of more wear and tear, so it needs regular maintenance, often to increase the life of the bearing. In the daily work of the crusher, equipment lubrication should be paid attention to and timely lubrication of the friction surface, which can ensure the normal operation of the equipment and effectively prolong the use time of the crusher. In general, the grease in the bearing seat is added to the 50-70% of the volume, and must be replaced every three months. When the oil is changed, the runway of the bearing roller is carefully cleaned with clean gasoline or kerosene.


Top